I have quite an extensive collection of media that my server makes available through different means (Jellyfin, NFS, mostly). One of my harddrives has some concerning smart values so I want to replace it. What are good harddrives to buy today? Are there any important tech specs to look out for? In the past I didn’t give this too much attention and it didn’t bite me, yet. But if I’m gonna buy a new drive now, I might as well…
I’m looking for something from 4TB upwards. I think I remember that drives with very high capacity are more likely to fail sooner - is that correct? How about different brands - do any have particularly good or bad reputation?
Thanks for any hints!
You must log in or register to comment.
Buy recertified enterprise grade disks from https://serverpartdeals.com. Prices were around $160/16TB the last time I checked. Mix brands and models to reduce simultaneous failure. Use more than 1-disk redundancy. If you can’t buy from SPD, either find an alternative or buy external drives and shuck them. Use ZFS to know if your data is correct. I’ve been dealing with funny AMD USB controllers recently and the amount of silent data corruption I’d have gotten if not for ZFS is ridiculous.
Damn I just put 32 more TBs in my homelab and wish I would have known about this site.
This is incredible!
American sites like this so rarely ship to France, or it costs a litteral fortune just in shipping, here it’s 130€ for a 12TB shipping included!
Wow.
I Do Not Need A 12TB Hard drive.
I Do Not Need a 12 TB Hard drive!
I mean or do I?
Thanks 💖
Holy cow these are way cheaper than anything I have seen before. I am in a RAID 5 setup so if a disk or two dies I am okay.
Yep, I have 6 14tb drives from them in raid10.
Three-way mirror?
I would not trust these kind of dives in the mirror. IMHO RAID6 is the only way.
Due to risk of failure or risk of data corruption because the mirror can’t tell which drive is right when there’s a difference?
I use BTRFS for the same. Being able to check for and repair silent corruptions is a must (and this is without needing to read the whole drives, only the actual files). I’ve had a lot of them over the years, including (but not only) because of a cheap USB controller also.
There are two types, CMR and SMR. You can read online about the differences. CMR is better because SMR tries to be all fancy in order to increase capacity, but at the cost of speed and data integrity.
It won’t be front and center in the specs of a particular drive, but you usually find the info somewhere.
I wouldn’t worry about higher capacity failing sooner. If you have 10x4TB vs 2x20TB, that’s 5x as many drives to go bad. So a 20TB drive would need a 5x worse fail rate to be considered worse. A pro of larger (fewer) drives is lower power consumption. 5-10 watts per drive doesn’t sound like much, but it adds up.
If you are buying used datacenter drives, larger capacity drives are also likely to be newer, which tips the scales a little more in that direction.
My last I have bought are the Toshiba N300 15tb helium drives.
Didnt write much to it but they were cheap and seemed quiet enough to have around in my room (where I also sleep)Any hard drive can fail at any time with or without warning. Worrying too much about individual drive families’ reliability isn’t worth it if you’re dealing with few drives. Worry instead about backups and recovery plans in case it does happen.
Bigger drives have significantly lower power usage per TB, and cost per TB is lowest around 12-16TB. Bigger drives also lets you fit more storage in a given box. Drives 12TB and up are all currently helium filled which run significantly cooler.
Two preferred options in the data hoarder communities are shucking (external drives are cheaper than internal, so remove the case) and buying refurb or grey market drives from vendors like Server Supply or Water Panther. In both cases, the savings are usually big enough that you can simply buy an extra drive to make up for any loss of warranty.
Under US$15/TB is typically a ‘good’ price.
For media serving and deep storage, HDDs are still fine and cheap. For general file storage, consider SSDs to improve IOPS.
Check out blackblaze drive stats, https://www.backblaze.com/cloud-storage/resources/hard-drive-test-data
One thing no one will tell you HOW LOUD some HDDs could get under load. You may not want any of those disks around if you’re keeping your server around your living spaces.
Just check dB values in the spec sheets.
I’d like to second the ‘manufacturer doesn’t matter, all drives are going to fail’ line, but specific models from manufacturers will have a much higher failure rate than others.
Backblaze, for example, publishes quarterly(ish?) stats showing the drives with the highest failure rates in terms of percentages, so you can kind of get a good view on if there’s a specific drive model you should maybe avoid.
Or just buy an actual enterprise drive, avoid SMR, and have backups is also a sane approach.
One important thing, ensure the drive is CMR, the reason is that you likely want a RAID, and non-CMR disks take so long to read the entire disk that the chances of a second failure while recovering from a disk failure is significant.
That being said, how are you keeping track of the disks state? I built my RAID recently, and your post made me realize that I have nothing to notify me if one of the disks shows early signs of problems.
I just use the built-in email function that comes with mdadm. If a drive fails, I’ll know right away and replace it with a spare. You do need your server to be able to send emails with something like postfix.
If you have hardware RAID, there’s often a monitoring tool that comes with it or at the very least a command-line utility that can report the RAID state which you can then use in a script.
After I had two WD drives fail in my old NAS so I switched to all Seagate on my next build. Currently running 9x 20TB Exos X20, though for only about a year now, so no issues should be expected, yet.
I think the most important thing is that you pick a drive that is meant for NAS/server use (so rated for running 24/7). And having manufacturere warrenty is also nice. My Seagate drives have 60 months (which is considerably more then the 36 months that my WD drives had).
my currently failing drive is a WD as well… 🥴 I bought it a year ago, I think…
Switching wholesale from a brand or model to another could be counterproductive. There are myriad of reasons why drives can fail that aren’t related to the brand and the model. What if you unknowingly switch to a less reliable model because of such a reason? You’d end up worse off. For example according to Backblaze’s data, Seagate is generally worse than WD.
A better way to do this is to mix brands and models so that there’s less probability to fail at the same time. I have both WD and Seagate in a single storage pool, even if the Seagate model is objectively less reliable according to Backblaze.
I would say Seagate Exos or Western Digital Ultrastar.
I’d start with Backblaze’s 2023 drive report
I’m looking for something from 4TB upwards.
If you say “harddrive” … do you mean actual harddrives or are you using it synonymous with “storage”? If you really talk about actual harddrives, it’s hard to even find datacenter/server harddrives below 4 TB. Usually server HDDs start with 8 or 12 TB. You can even find HDDs with 20 TB - Seagate Exos series for example, starting at around 360 Euros (ca. 400 USD).
If you’re in for a general storage, preferably SSD, that’s another issue. There is the Samsung 870 QVO (8 TB) SSD that is often advertised as “datacenter SSD” (so I assume it would run well in a server that is active 24/7), but it is currently available with a maximum of 8 TB. The 870 QVO is at ca. 70 Euros per terabyte (ca. 77 USD) which, in my experience, is the current price range for SSDs. So it has a high price seen from the outside but it’s actually fine. It’s also a one-time investment.
For selfhosting I’d go with an SSD-only setup.
do any have particularly good or bad reputation?
From personal experience I’d say, stick with the “larger” brands like Samsung or Seagate.
I was thinking actual hard drives, not SSDs…
Okay, so … then maybe really look into the Seagate Exos drives. 20 TB should be pretty much fine for most selfhosting adventures.
I have a few of those, and while the ones I bought have worked out fine so far, I think it’s worth cautioning people that they are annoyingly loud doing basic operations.
